{"id":85,"date":"2015-11-01T09:12:31","date_gmt":"2015-11-01T14:12:31","guid":{"rendered":"http:\/\/getbetteraudio.com\/?p=85"},"modified":"2015-11-18T20:52:19","modified_gmt":"2015-11-19T01:52:19","slug":"skypemixer","status":"publish","type":"post","link":"https:\/\/getbetteraudio.com\/studio\/skypemixer\/","title":{"rendered":"Interfacing Skype with a Mixer"},"content":{"rendered":"

\"01<\/a>If you\u2019re connecting your Skype computer to your mixer with analog cables, make sure you\u2019re doing it correctly. Be aware that there is one little issue that can damage or at least compromise the performance of some computers.<\/p>\n

THE INPUT SIDE<\/strong><\/p>\n

\"02<\/a>Most Internet broadcasters and podcasters are (or should be) using an auxiliary send on the mixer to send a mix-minus feed to Skype. That feed is mono. Most desktop and USB computer sound cards have stereo inputs. Skype really only looks at the left channel for its input, but some cheap, no-name sound cards may\u00a0actually get the channels reversed internally. Therefore, it\u2019s a good idea to feed the audio from the aux send on the mixer to both the left and right channels of the computer sound card.<\/p>\n

<\/p>\n

In a typical installation, the cable needed will be a \u00bc\u201d two-conductor (TS) cable plugged into the aux send on the mixer and a \u215b\u201d three-conductor (TRS) cable plugged into the computer sound card on the other end. To get mono audio from the aux send to both stereo channel inputs on the computer sound card, the tip and ring (TR) connections on the \u215b\u201d plug need to be shorted together. If you make your own cable, simply connect both of the left and right hot wires (tips) from the \u215b\u201d plug to the hot wire (tip) of the \u00bc\u201d plug. With a USB sound card, the inputs are often RCA jacks instead of \u215b\u201d jacks. In that case, the hot wires of each RCA plug (tips) are also connected together at the tip of the \u00bc\u201d plug.<\/p>\n

\"03<\/a>

Hosa CMP-105<\/p><\/div>\n

You can \u201cmake\u201d this cord by using adapters from Radio Shack, but using adapters should be a last resort to getting or making the right cable. Every time you add a connection, you add a potential point of failure. Anyone who has used adapters on audio cables has probably experienced a flaky connection because of adapters. If you have not had a problem yet, you will.<\/p>\n

A good solution is to use the Hosa CMP-105 cable, pictured here. The CMP-105 has a \u215b\u201d TRS plug on one end and a \u00bc\u201d TS plug on the other. The tip of the \u00bc\u201d plug is connected to the tip and ring of the \u215b\u201d TRS plug. The \u00bc\u201d mono plug connects to the mixer\u2019s aux out jack, and the \u215b\u201d plug connects to the computer sound card. Even though Skype is mono and only sees the left channel of the audio input, the CMP-105 causes audio to appear on both the left and right inputs of the computer sound card. If the card is miswired internally, it doesn\u2019t matter since audio appears on both the left and the right channel inputs. If the card is wired correctly, it simply ignores the audio on the right channel.<\/p>\n

THE OUTPUT SIDE<\/strong><\/p>\n

Connecting the output of a computer or USB sound card to a mixer can be tricky. Like the input side, most computer sound cards have a stereo output. If you have a stereo channel on your mixer that you don\u2019t need for a stereo source, get a \u215b\u201d stereo (TRS) cable as above that has two \u00bc\u201d mono (TS) plugs for the left and right channels. The Hosa CMP-159 is a good choice. Plug the \u215b\u201d plug into the computer card, and plug the left and right channel mono plugs into the left and right inputs on the mixer.<\/p>\n

\"04<\/a>

Hosa CMP-159<\/p><\/div>\n

Remember that since Skype is mono, it\u2019s a waste of a stereo channel to use it for Skype. Most mixers have more mono channels than they do stereo channels. It makes sense to consider using a mono channel for Skype.<\/p>\n

Unlike the input side, it is not a good idea to short the left and right channels on the output of the sound card together. The explanation is very technical (the output impedance of each output is lower than the other channel is able to drive without damage or distortion), and not every sound card suffers from the issue (for example, if the outputs have a series resistor). The CMP-105 used above for the input side should not be used to connect the output of the sound card to the mixer. That cord shorts the two sound card outputs, and that\u2019s a bad idea.<\/p>\n

\"05<\/a>

CMM-115<\/p><\/div>\n

A safe solution is simply to connect the left channel of your sound card to the line input of a mono channel on your mixer. If you want, you can get the same CMP-159 \u215b\u201d stereo to \u00bc\u201d dual mono cord and connect only the left channel \u00bc\u201d mono plug to the mixer. That is, you only connect the\u00a0gray plug to the mixer. Leave the orange plug floating, but don\u2019t let it short against anything. You can \u201cmake\u201d a cord using adapters from Radio Shack. Read the warning above about adapters.<\/p>\n

If you make your own cords like I do, you can get a \u215b\u201d stereo to \u215b\u201d stereo cable, cut it in half, and solder on a \u00bc\u201d mono plug connecting only the left channel hot wire to the \u00bc\u201d tip and the left channel shield to the shield on the \u00bc\u201d plug. Avoid unshielded \u215b\u201d to \u215b\u201d cables intended for speakers. The shield inside the cable is necessary to prevent noise in your audio. The 15 foot Hosa CMM-115 cable, shown here, will allow you to make two 7-\u00bd foot cables with molded \u215b\u201d TRS connectors on one end and the connector of your choice on the other.<\/p>\n

CONCLUSION<\/strong><\/p>\n

\"06<\/a>

Hosa CMR-206<\/p><\/div>\n

As always, there can be exceptions to the general rules posted here. For example, sometimes when you connect a computer\u00a0to a\u00a0mixer, you get a ground loop. That ground loop puts a horrible whining noise into your audio. A good way to eliminate the ground loop and the noise is to add a group loop isolator. If you have to add one, the connections described in this article may not be the right ones. Fortunately, Hosa and many other manufacturers make cables that allow you to connect almost anything to almost anything else. A \u215b\u201d stereo plug to two mono RCA plug cable, like the CMR-206, is necessary for some installations, such as connecting the Tape Output of a mixer to an external recorder.<\/p>\n

\"07<\/a><\/p>\n

Be sure you understand the details discussed here so that you get the right cables. When you order cables, get a couple of spares. Note that the Hosa cable numbers given here are for specific lengths. If you need a cable that is longer or shorter, the model number will be slightly different.<\/p>\n

If you have questions about anything mentioned in this article, you can reach me through Twitter at@mcphillips<\/strong><\/a>. There are more tips and tricks at http:\/\/mikephillips.me<\/strong><\/a>. Thanks to Hosa for providing the pictures for this article. Hosa cables are available through Amazon.com and many professional audio dealers.<\/p>\n","protected":false},"excerpt":{"rendered":"

If you\u2019re connecting your Skype computer to your mixer with analog cables, make sure you\u2019re doing it correctly. Be aware that there is one little issue that can damage or at least compromise the performance of some computers. THE INPUT SIDE Most Internet broadcasters and podcasters are (or should be) using an auxiliary send on […]<\/p>\n","protected":false},"author":2,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_genesis_hide_title":false,"_genesis_hide_breadcrumbs":false,"_genesis_hide_singular_image":false,"_genesis_hide_footer_widgets":false,"_genesis_custom_body_class":"","_genesis_custom_post_class":"","_genesis_layout":""},"categories":[5,6],"tags":[8],"_links":{"self":[{"href":"https:\/\/getbetteraudio.com\/studio\/wp-json\/wp\/v2\/posts\/85"}],"collection":[{"href":"https:\/\/getbetteraudio.com\/studio\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/getbetteraudio.com\/studio\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/getbetteraudio.com\/studio\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/getbetteraudio.com\/studio\/wp-json\/wp\/v2\/comments?post=85"}],"version-history":[{"count":21,"href":"https:\/\/getbetteraudio.com\/studio\/wp-json\/wp\/v2\/posts\/85\/revisions"}],"predecessor-version":[{"id":140,"href":"https:\/\/getbetteraudio.com\/studio\/wp-json\/wp\/v2\/posts\/85\/revisions\/140"}],"wp:attachment":[{"href":"https:\/\/getbetteraudio.com\/studio\/wp-json\/wp\/v2\/media?parent=85"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/getbetteraudio.com\/studio\/wp-json\/wp\/v2\/categories?post=85"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/getbetteraudio.com\/studio\/wp-json\/wp\/v2\/tags?post=85"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}